Weekend warrior here with almost no networking experience. I moved into a new house that was pre wired with cat5e but no patch panel. Just loose ends in the basement. I have been hooking each room up to a patch panel I bought. On the last room I am seeing strange behavior in my tester. When I plug the tester onto the line all of the lights come on even though the remote is not attached to the line. On both ends(patch panel and upstairs room). When the remote is attached, only line 6 turns on on the remote. I am not able to get any internet connectivity through the connected line right now. What could cause the tester to think the remote is connected when it isn’t? Does this mean I have a short in the wire in the wall somewhere?
If the twisted pairs weren’t correct I would expect the tester sequence to be out of order when the remote is connected. My tester is showing the proper order when the remote end is not even connected which didn’t make sense to me. I don’t understand how the tester can show a proper set up when the remote is not attached to verify the setup.
Thank you. Will try that. I really hope I don’t have to run a new line
Weekend warrior here with almost no networking experience. I moved into a new house that was pre wired with cat5e but no patch panel. Just loose ends in the basement. I have been hooking each room up to a patch panel I bought. On the last room I am seeing strange behavior in my tester. When I plug the tester onto the line all of the lights come on even though the remote is not attached to the line. On both ends(patch panel and upstairs room). When the remote is attached, only line 6 turns on on the remote. I am not able to get any internet connectivity through the connected line right now. What could cause the tester to think the remote is connected when it isn’t? Does this mean I have a short in the wire in the wall somewhere?
Cheers to the ones that JUST miss out 🍻
I just found out I was at 41.4 degrees north so I can’t participate either. 😩
I’m not very mechanically inclined so I purchased. The hoist is Lange power hoist and the brackets I found on amazon.
Very cool! Something else, 9:15 am is UTC time for when Marty was supposed to be at Twin Pines Mall (1:15am pacific time). Would have been better if it was 9:34 am (1:34 am PT) for when he actually went back in time.
I’ve used drawio for similar types of diagrams.
I live in Bethany and this is the first I’m hearing of it as well!
Did you replaced the faded plastics or use a conditioner to bring back the blacks?
Do you not worry about getting pulled over due to not having side mirrors?
Thanks for the tip. I’ve heard about Turtle Wax Ice on plastics but wasn’t sure if it was just a gimmick.
What’s your wax of choice? Do you use anything to protect the plastic?
Thanks for the heads up on the loop length. I hadn’t considered that. I was going to give them my 1TB external drive so that daily they could move the files off of the SD card. But having a couple SD cards wouldn’t hurt either.
Thanks for the concern. The RV already has a backup camera with a nice big display in the cab, so that isn’t an issue. Having a dual camera system would be redundant for reversing for them.
Suggestions for RV dashcam
I’m sorry if this has already been asked before but I wasn’t able to find anything.
My parents are looking to take a road trip in an RV. They want to record the journey. I was looking though some of the suggested cams but I’m not sure if there is anything specific with an RV that I need to be aware of when it comes to dash cams. Does anyone have any suggestions for cams specifically for RVs?
I imagine that they will need to clean the SD card daily so a camera that is user friendly to a not very tech savvy user is a must. They also do not think they want a dual camera system due to the installation of the second camera and they don’t really care about what will be behind them.
Any suggestions would be greatly appreciated! Thanks!
You have to install it manually. It’s not released yet. Someone has built the app and is sharing for people to try: https://reddit.com/r/programming/comments/bltm2e/the_new_windows_terminal_youtube_promo/emrljnz
Same for my wrangler. Started this shake around 20k miles. I thought it was start of death wobble. Dealer replaced the stabilizer and haven’t had the problem since
Interstate bumps causing major oscillation at 80mph. 23 JL. What’s going on?
Wrangler